Hitec D956WP 32-Bit High Torque WP Steel Gear Servo (HRC36956)
$109.99
Skip to product information
Hitec D956WP 32-Bit High Torque WP Steel Gear Servo (HRC36956)
$109.99
Extreme Torque
Up to 405 oz in Power
IP67 Waterproof
Dust and Water Resistant Housing
32-Bit Tech
High Resolution Microcontroller Precision
Steel Gears
Ultra Durable Steel Alloy Drive
Coreless Motor
Fast Response Metal Brush Performance
Programmable PWM
Custom Endpoints and Soft Start
Torque Meets PrecisionUltimate Waterproof Steering Upgrade For Crawlers
The D956WP 32-Bit High Torque Waterproof Servo delivers top-tier performance and rugged reliability for 1/10-scale RC car enthusiasts, rock crawlers, and off-road bashers. Powered by an advanced 32-bit MCU and 12-bit ADC industrial circuitry, this high-performance waterproof RC servo provides ultra-precise control with up to 405 oz-in of raw steering torque.
Unmatched Power And ControlAdvanced 32-Bit Technology Built For Rock Crawling
Upgrade your radio control rig with the high-performance D956WP 32-Bit High Torque Waterproof Servo. Designed as an industrial-grade solution based on the proven D954SW, the D956WP servo features a diamond-cut aluminum heat sink center case and nylon-reinforced upper and lower covers to withstand demanding off-road action. Inside, a coreless metal brush motor operates alongside hardened steel alloy gears and a dual-ball-bearing supported 25-tooth output shaft to ensure maximum durability under heavy loads. With a wide operating voltage range from 4.8V to 7.4V DC and deep digital programmability—including end-point adjustment, dead band, fail-safe, and soft start rate—the D956WP waterproof steel gear servo offers unmatched custom tuning for your crawler or truck.
Technical SpecificationsComplete Performance Data And Measurements
Compatible Vehicles
1/10-Scale RC Cars, Rock Crawlers & Off-Road Trucks
Part Type
High Torque Waterproof Servo
Operating Voltage
4.8V ~ 7.4V DC
Speed (60°)
0.19 sec @ 4.8V - 0.12 sec @ 7.4V
Maximum Torque
251 oz-in (18.0 kg-cm) @ 4.8V - 405 oz-in (29.0 kg-cm) @ 7.4V (gauge)
Circuit Type
32-Bit Programmable Digital MCU with 12-Bit ADC
Motor Type
Coreless Metal Brush Motor
Gear Material
Karbonite 1st Gear & 3 Steel Alloy Gears
Bearing Type
Dual Ball Bearing Output Shaft
Output Shaft
25-Tooth Spline / H25T
Case Material
Plastic Upper/Lower & Diamond-Cut Aluminum Heat Sink Center
Dust/Water Resistance
IP67 Rating Waterproof
Current Draw
Idle 30 mA / No Load 500 mA / Stall 5200 mA
Dimensions
1.57 x 0.78 x 1.46 in / 40.0 x 20.0 x 37.0 mm
Weight
2.40 oz / 68.0 g
Connector Gauge
20 AWG / 80 Strand
Key Servo CapabilitiesEngineered For Durability And High Speed Response
Digital ProcessingProgrammable PWM amplifier with 32-bit MCU and 12-bit ADC circuitry
High Resolution4096 resolution paired with a 1M cycle long-life potentiometer
Waterproof ProtectionIP67 rated dust-resistant and fully waterproof case
Heavy Duty DrivetrainHardened steel output shaft supported by dual ball bearings
Superior CoolingDiamond-cut aluminum heat sink center housing
Standard Spline25-tooth output spline for broad servo horn compatibility
Wide Voltage SupportOperating voltage range extending from 4.8V to 8.4V DC
Programmable FunctionsEndpoint adjustment, direction, fail-safe, dead band, speed, and soft start rate
Frequently Asked QuestionsEverything you need to know
Is the D956WP High Torque Servo fully waterproof?
Yes, the D956WP High Torque Servo features an official IP67 dust and waterproof rating, making it completely protected against water submersion, wet trails, mud, and dust during intense off-road driving.
What scale RC vehicles are recommended for the D956WP Servo?
The D956WP Servo is designed primarily for 1/10-scale RC cars, rock crawlers, trail trucks, and off-road bashers that require high steering torque and reliable gear strength.
Can I program custom settings on the D956WP Servo?
Yes, the D956WP Servo features a 32-bit programmable digital circuit that allows users to adjust endpoints, direction, fail-safe, dead band width, speed, and soft start rate using a compatible servo programmer.
What horn spline size does the D956WP Servo output shaft use?
The D956WP Servo utilizes a standard 25-tooth output spline (H25T), making it directly compatible with most standard 25T aluminum and composite servo horns.
Customers Also Bought
No related products found.