Learning Center

Stripped Steering Servo? How to Rebuild a Traxxas 2085 with Plastic or Metal Gears

💥 RC Basher DeskBy Bash Brody 6 min read
Traxxas 2087X metal gear set for 2085 and 2085X servos
Hobbyists since 1978 Written by our staff who race, fly and build Questions? 678-513-4450
💥 RC Basher DeskBy Bash BrodyUpdated November 19, 20267 min read
Traxxas 2087X metal gear set for 2085 and 2085X servos
The Traxxas 2087X metal gear set fits the 2085, 2085X and 2085XL Maxx-size servos. — view at Atlanta Hobby

You turn the wheel on your transmitter, the servo makes a clicking noise, and the front wheels barely move. Traxxas's own support answer for that symptom is a stripped servo gear. The good news is that the 2085-family servos used on Maxx-size Traxxas trucks can be rebuilt with a gear set that costs a fraction of a new servo.

This guide covers how to confirm a stripped gear, which Traxxas gear set fits your servo, and how to swap the gears. If you are shopping for a whole new servo instead, see our steering servo guide.

The Short Answer

Symptom: a clicking sound when you steer and wheels that do not turn usually points to a stripped servo gear (Traxxas).

Fix: a standard 2085 takes the 2087 gear set ($15.00). A 2085X or 2085XL takes the 2087X metal gear set ($30.00), which can also convert a standard 2085 to all-metal gears if you swap every gear (Traxxas).

1. Is It Really a Stripped Servo Gear?

Traxxas's support answer for a clicking sound with wheels that don't turn is direct: "Sounds like you may have a stripped servo gear." To check, remove the four screws on the bottom of the servo case, lift off the top and look at the gears. If a gear is stripped, rebuild the servo with a replacement gear set (Traxxas).

Rule out the other steering problem

If the throttle works but there is no steering at all, Traxxas has a separate troubleshooting guide for that case (Traxxas). A clicking servo with wheels that won't turn is the stripped-gear sign.

2. Which Gear Set Fits Your Servo?

Your servo Gear set Notes
2085 (standard) 2087 Replacement gears and bearings; does not fit 2085X or 2085R (Traxxas)
2085X / 2085XL 2087X (metal) Replacement metal gears; bearings not included (Traxxas)
2085 (upgrade) 2087X (metal) All-metal upgrade; "must swap all gears" (Traxxas)

Traxxas lists the 2087X as a stock part for the X-Maxx, X-Maxx Ultimate, X-Monster chassis, XRT and Funco Pro Scale Replica, and as an accessory for the Maxx and Maxx Slash (Traxxas). The Maxx parts list describes the 2087X as the metal gear set "for 2085, 2085X, 2085XL servos" (Traxxas Maxx parts list).

Not sure which servo you have?

Check the part number on the servo case. The 2085XL and 2085L both require the Maxx-style mount found in Maxx and X-Series trucks (Traxxas, Traxxas). Traxxas says the 2087 does not fit the higher-torque 2085R, so check the parts list for your exact servo before ordering (Traxxas).

3. Plastic or Metal: Should You Upgrade?

Traxxas says "metal-gear servos offer greater strength and durability compared to servos with composite gears" (Traxxas). At the same time, Traxxas notes that "many servos use plastic gears, and they work well for most 1/10 scale RC car and truck applications" (Traxxas).

When the 2087 makes sense

If your standard 2085 lasted a long time before it stripped, the $15.00 2087 set restores it and includes bearings (Traxxas).

When the 2087X makes sense

If you keep stripping gears, the 2087X converts a standard 2085 to an all-metal gear train, as long as you replace every gear (Traxxas). For a 2085X or 2085XL, the 2087X is simply the correct replacement.

When to replace the whole servo

Traxxas says the 2085XL puts out 23% more torque than the standard 2085 and has full metal gears (Traxxas). If you want more steering authority, replacing the servo may be the better move.

4. How to Swap Servo Gears, Step by Step

Traxxas's metal-gear servo upgrade article walks through the process on a different servo (the 2075 with a 2072X gear set), but the method carries over. Always follow the exploded view that comes with your gear set for the exact gear order (Traxxas).

You will need: a no. 1 Phillips screwdriver and the white lithium grease included with Traxxas metal gear sets.

  1. Center the servo. Power up the truck and transmitter, set the steering trim to zero so the servo centers, then power both off.
  2. Remove the servo. Take off the servo horn or servo saver, unbolt the servo and unplug it from the receiver. Keep the output shaft in its centered position.
  3. Open the case. Remove the four screws on the bottom and lift the case top straight up. If the output shaft lifts with it, press it back down.
  4. Take a photo. Note where every gear, bearing, bushing and O-ring sits before you remove anything.
  5. Remove the old gears. Lift each gear straight up, save any bearings you need to reuse, and clean off the old grease.
  6. Install the new gears. Start with the lowest gear and its axle, then stack the rest, greasing the teeth and shafts as you go.
  7. Close it up. Make sure the output shaft O-ring and case gasket are in place, seat the case top and snug the four screws.
  8. Test before reinstalling. Plug the servo in, power up and check that it operates before you bolt it back in.

Steps adapted from Traxxas.

Don't overtighten the case screws

Traxxas warns: "Be careful not to overtighten them, or you may damage the tiny o-rings on the screws" (Traxxas).

Bearings for the 2087X

The 2087X does not include bearings (Traxxas), so plan to reuse the bearings from your servo when you swap the gears.

5. Check the Servo Saver Too

On Maxx-size trucks, the servo saver spring matters. Traxxas says the 2085X comes with a "super-stiff servo saver spring" that helps keep the bellcranks from "camming out" too easily (Traxxas). After a rebuild, check that your servo saver and bellcranks are in good shape.

Make it part of your routine

Add a quick steering check to your post-run maintenance checklist: turn the wheel lock to lock and listen for clicks before they turn into a stripped gear.

Conclusion

A clicking steering servo on a Traxxas Maxx or X-series truck is usually a stripped gear, and the fix is a gear set and a screwdriver. Use the 2087 to restore a standard 2085, the 2087X for a 2085X or 2085XL or to convert a 2085 to metal gears, and consider a 2085XL if you want more torque. Need a hand? Bring your truck by the store and we will take a look.

Gear Mentioned in This Guide

Traxxas 2087 replacement gear set for the 2085 servo

Traxxas Gear Set (for 2085 Servo) (2087)

$15.00: the replacement gear set (with bearings) for a standard 2085 servo.

Shop now
Traxxas 2087X metal gear set for 2085 and 2085X servos

Traxxas Gear Set, Metal (for 2085 & 2085X Servo) (2087X)

$30.00: an all-metal gear train for the 2085X/2085XL, or an upgrade for a standard 2085 (swap every gear).

Shop now
Traxxas 2085XL high-torque metal gear servo

Traxxas Servo High Torque Digital Metal Gear (2085XL)

$99.95: a complete metal-gear Maxx servo if you would rather replace than rebuild.

Shop now

Frequently Asked Questions

Why does my RC steering click but not turn?

According to Traxxas, a clicking sound with wheels that don't turn usually means a stripped servo gear. Open the case and inspect the gears (Traxxas).

Does the 2087 gear set fit a 2085X servo?

No. Traxxas says the 2087 does not fit the 2085X or 2085R. Use the 2087X metal gear set for the 2085X and 2085XL (Traxxas, Traxxas).

Can I put metal gears in a standard 2085?

Yes. Traxxas says the 2087X can upgrade a standard 2085 to an all-metal gear train, but you must swap all the gears (Traxxas).

Are metal servo gears worth it?

Traxxas says metal-gear servos are stronger and more durable than composite-gear servos, though plastic gears work well for most 1/10 scale cars and trucks (Traxxas, Traxxas).

What grease goes on servo gears?

Traxxas's procedure uses the white lithium grease included with its metal gear sets, applied to the gear teeth and shafts during assembly (Traxxas).

Sources and Further Reading

Atlanta Hobby

Talk to a real hobbyist.

Our staff have been racing, flying and building since 1978. Call, stop by the store, or bring it in for repair.