
Combat robotics is the only branch of engineering where a successful test ends with your project in pieces and you smiling about it. It is also one of the best ways I know to learn design under pressure: every gram has to justify itself, every screw gets tested by something trying to remove it, and you find out in three minutes whether your idea works.
The good news for beginners is that the sport has small classes. You don't need a 250 lb monster or a machine shop. A 1 lb antweight fits in a lunchbox, runs on parts from the RC world, and fights in a polycarbonate box. This guide covers the weight classes, the safety rules your robot must pass at the inspection table, and how to plan a first antweight that actually drives onto the arena floor. Rules references are to the SPARC Robot Construction Specifications current as of August 2026.
The Short Answer
Most beginners should start in the 150 g fairyweight or 1 lb antweight class with a simple wedge or lifter, a radio that stops the robot on signal loss, a manual power switch or removable link, and a power light, because those are the safety basics inspection checks first.
- Classes: 150 g, 1 lb, 3 lb, 12 lb and 30 lb are the common small-to-mid classes in the US.
- Safety rules: SPARC requires a visible weapon lock outside the arena, a manual disconnect reachable within 15 seconds, and spinners that stop within 60 seconds.
- First design: a wedge or lifter wins more beginner fights than a spinner that tears itself apart.
- Batteries: LiPos are allowed, but terminals must be protected and damaged packs need careful handling.
1. Weight Classes: Why Small Is Smart
Robots fight within weight classes, and the class you pick sets your budget, your repair time and how dangerous testing is. Make: Magazine's field guide to combat robot classes lists the common steps from 150 g up to 30 lb. Here is how they line up for a new builder:
| Class | Weight limit | Good for |
|---|---|---|
| Fairyweight (UK "antweight") | 150 g | The cheapest way in; often 3D-printed and quick to repair |
| Antweight (US) | 1 lb (454 g) | First builds with a real weapon budget; this guide's focus |
| Beetleweight | 3 lb (1.5 kg in the UK) | Second robot; parts and repairs start to cost real money |
| Hobbyweight | 12 lb | Experienced builders; much more energy in the weapon |
| Featherweight | 30 lb | Serious machining, serious arenas, serious safety |
Start at 150 g or 1 lb
The Robot Combat Wiki getting-started guide says a beginner's best bet is often the 150 g class, because those robots are small, inexpensive and easy to repair, and local events almost always run it. Most builders start in the "insect" classes for the same reason. If you want room for a working weapon and slightly tougher parts, 1 lb antweight is the next step and is the focus of the rest of this guide.
Weight bonuses for unusual locomotion
Wheels are the default. SPARC's Robot Construction Specifications (v1.6) give a weight bonus to robots that move differently: 1.25x for shufflers, 1.5x for non-traditional designs and 2x for true walkers. A walking antweight can weigh up to 2 lb. It is a fun engineering challenge, but legs are slow and fragile, so it is not a common first build.
Weigh everything, early
Get a kitchen scale that reads in grams and weigh every part before you design around it. Builders keep a spreadsheet of every component, screw and wire. Leave a margin: you will add zip ties, heat-shrink and a bigger wedge before the event, and robots are weighed at check-in. Over is over.
2. The Safety Rules Your Robot Must Pass
Most US events use, or borrow heavily from, the SPARC standards (Standardized Procedures for the Advancement of Robot Combat). Your robot goes through a safety inspection before it fights, and these are the items inspectors care about most. Always read your specific event's rules, because organizers can add to or change them.
Failsafe: stop when the signal stops
SPARC section 6.4.1 requires radio systems that stop all motion when the transmitter loses power or signal for robots with active weapons or over 12 lb, and notes that robots 1 lb and under are typically required to have drive failsafes. In plain terms: switch off your transmitter while the robot is driving on blocks, and everything must stop. Test this at home, with the wheels off the ground, before you ever enter an event. The Robot Combat Wiki recommends confirming the failsafe with only the drive motors connected first.
Power switch, power light and weapon lock
SPARC requires a manual disconnect for all drive and weapon power (a switch or removable link, not just a relay) that can be operated within 15 seconds without putting the operator at risk, and full deactivation in under 60 seconds. You also need a light visible from outside the robot showing main power is on. Any weapon needs a clearly visible locking device whenever the robot is outside the arena, and locking pins must be in place during power-on.
Spinners and banned weapons
Spinning weapons must come to a full stop within 60 seconds of power being removed, using a self-contained brake. SPARC also prohibits several weapon types outright, including electrical weapons, RF jamming, entangling devices, liquids and powders, untethered projectiles, fire and explosives, and smoke or lights that impair viewing.
Safe power-up, every time
- Weapon lock installed and the robot pointed away from people.
- Transmitter on first, throttle and weapon controls at zero.
- Robot power on (switch or link), and confirm the power light is lit.
- Check drive response with wheels off the table.
- Only in the arena, with the door closed, remove the weapon lock.
- After the match: robot power off first, lock back in, then the transmitter.

3. Planning Your First Antweight
A first antweight should be simple, robust and easy to fix between matches. That usually means two-wheel drive, a wedge or a servo lifter, and a 3D-printed or plastic chassis. A good finish line for your first event is driving every match and not getting disqualified at inspection.
Pick a weapon that won't beat you
Make's guide describes the main weapon families: vertical spinners, drums, horizontal spinners, wedges, lifters, flippers and hammers. It calls lifters the safest active-weapon option because they don't store energy. A wedge with good driving wins plenty of insect-class fights, and a lifter driven by a metal-gear servo adds a weapon without the testing danger of a spinner. Spinners are powerful, but they need a reinforced test box. The Robot Combat Wiki says weapon tests should be done in one.
The core electronics list
Every antweight needs the same handful of parts: two small drive gearmotors, a dual brushed ESC (or one ESC per motor), a 2.4 GHz receiver with failsafe, a small LiPo pack, a power switch or removable link, and an LED power light. If you add a lifter, a servo plugs straight into a spare receiver channel. Match the battery voltage to what your motors and ESC are rated for. More voltage means more speed, but it also means more heat and shorter motor life.
LiPo safety in a sport built on impacts
SPARC allows lithium batteries but requires that battery terminals be protected from direct shorts. In practice: insulate every exposed connection with heat-shrink, mount the pack where a weapon is least likely to reach it, and pad it. After a hard match, inspect the pack. A puffed, dented or punctured LiPo should be set aside in a fireproof container, not charged. Reedy's LiPo safety instructions spell out the charging rules: balance charge, use a fireproof container away from anything flammable, stop if a pack swells, and never leave a battery charging unattended. Damaged packs go to a hazardous-waste or battery recycling drop-off, not the trash.
Find an event, then build to its rules
RobotCombatEvents.com lists upcoming competitions by date, location and weight class, and shows whether registration is open. Pick one a few months out, read its rules, and build to that. The Robot Combat Wiki also suggests asking organizers if you can walk the pits at an event before you compete. Builders are famously generous with advice.

Conclusion
Your first antweight will probably lose a fight. What it will teach you is worth the entry fee: how to budget weight, how to design for repair, why a failsafe exists, and how to handle lithium batteries with respect. Start small, pass inspection, drive every match, and then decide whether your second robot gets a spinner.
We stock the RC-side parts that go into insect-class bots: servos, small LiPos, chargers and LiPo safety gear. Browse our servo collection, or contact the shop and bring your design sketch to our Cumming showroom.
Gear Mentioned in This Guide

Spektrum 3S 450mAh 11.1V 50C LiPo
A small 3S pack size that insect-class builders often design around. Check your motors' voltage rating first.
Shop now
LiPo Battery Charging Safety Bag with Zipper
Charge and store your pit batteries in one. Combat packs take hits that ordinary RC packs never see.
Shop now
Hitec RDX2 Mini AC Balance Charger
A compact balance charger for the pit table between matches.
Shop now
Hitec HS-5065MG Sub-Micro Digital Metal Gear Servo
Metal gears for a beginner-friendly servo lifter arm on a small bot.
Shop now
Trinity TK950 Digital Soldering Station
You will re-solder motor leads and connectors after every event. A temperature-controlled iron helps.
Shop nowFrequently Asked Questions
What is the best weight class for a first combat robot?
The 150 g fairyweight or the 1 lb antweight. Both are inexpensive, quick to repair and widely offered at local events. The Robot Combat Wiki suggests 150 g as a beginner's best bet; 1 lb gives a bit more room for a weapon.
How much does an antweight weigh?
An antweight's limit is 1 lb (454 g) in the US. Under SPARC rules, robots that walk get a 2x bonus, so a true walker can weigh up to 2 lb. Shufflers get 1.25x and non-traditional designs 1.5x.
What safety features does a combat robot need?
Under SPARC rules: a failsafe that stops the robot when signal is lost, a manual power switch or removable link that can be operated within 15 seconds, a visible power light, a visible weapon lock when outside the arena, and a self-contained brake that stops spinners within 60 seconds. Check your event's own rules too.
Are spinners a good first weapon?
Usually not. Spinners store a lot of energy, need a reinforced test box and are hard on your own parts. A wedge or a servo lifter is safer to test and teaches driving, which wins a lot of beginner fights.
Can I use LiPo batteries in a combat robot?
Yes. SPARC permits lithium batteries, but terminals must be protected from short circuits. Pad and protect the pack, inspect it after every match, and never charge a damaged or puffed pack.
How do I find a robot combat competition?
RobotCombatEvents.com lists upcoming events with dates, locations, weight classes and registration status. Read that event's rules before you finalize your design.
Sources and Further Reading
- SPARC: Standardized Procedures for the Advancement of Robot Combat
- SPARC Robot Construction Specifications v1.6
- Make: Know Your Combat Robots, a Field Guide to Weight Classes and Weapons
- Robot Combat Wiki: Getting Started
- RobotCombatEvents.com: Upcoming Events
- Reedy: LiPo Safety Instructions and Warnings
