
There is a moment every glider pilot remembers. The motor is off, the prop has folded back against the nose, and instead of sinking toward the grass the model's tail kicks up and it starts to climb. Nobody touched the throttle. The sun heated a patch of field, the air above it rose, and your glider found it. That is thermal soaring, and it is the quietest addiction in RC.
Georgia summers are made for it. This guide covers how to spot and work thermals, how to fly an electric glider so the motor helps instead of hurting, and how folding props work, including the ESC setting that trips up almost everyone. The thermal technique draws on Dave Garwood's classic Model Aviation primer; glider specifics come from E-flite's Conscendo Evolution manual.
The Short Answer
To thermal an RC glider, climb to a safe height, glide smoothly while watching for lift (tail rising, a wing wagging, hawks soaring), then circle tightly where the model climbs, keep airspeed up, drift with the thermal but never so far downwind you can't get back, and land into the wind.
- Speed is life: most glider crashes are stalls on launch or landing.
- Folding props cut drag in the glide; the blades fold only if the prop stops.
- ESC brake: turn it on for a folding prop. Spektrum Avian ESCs default to brake disabled, which lets the prop freewheel.
- Start simple: an electric glider with stabilization, like the Conscendo Evolution or UMX Conscendo, lets you climb again whenever you need.
1. Finding Thermals: Reading the Air
A thermal is a column or bubble of warm air rising from ground that heats faster than its surroundings: a parking lot, a plowed field, a dry hillside. You can't see the air, but you can see what it does to everything in it.
| Sign | What it suggests |
|---|---|
| Puffy cumulus clouds | A productive thermal day |
| Wind suddenly goes calm and warm at the flight line | You may be standing near a thermal's base |
| Wind picks up and feels cooler | Air is rushing toward a thermal forming nearby |
| Hawks soaring, small birds darting in one area, bugs or fluffy debris going up | Rising air carrying birds, insects or their food |
| Your glider's tail or nose rises, a wing wags, it speeds up or looks "nervous" | The model just flew into lift |
Adapted from Dave Garwood's "Introduction to Thermal Soaring," Model Aviation.
Watch the model, not just the sky
Garwood's best advice is to learn how your model behaves in lift, in sink and in neutral air. In lift the tail or nose rises, a wing lifts, or the whole model climbs. Fly it in calm evening air first so you know what "normal" looks like; then a thermal stands out.
Think about where lift drifts
Thermals drift with the wind. Garwood notes that a bubble of hot air over an open field may lift off when it reaches a tree line at the downwind edge. That makes downwind the natural place to search, but it is also where you lose height getting home. Search downwind only as far as your altitude lets you return to the landing area.
Pick your times
Midday sun on a day with puffy cumulus clouds is prime time. Garwood notes that cloud shade accentuates the ground-temperature differences that generate thermals. Early morning and late evening are usually smoother, which is ideal for learning trim and landings before you chase lift.
2. Flying a Thermal, Step by Step
The technique is the same for a pure sailplane on a hi-start and an electric glider. On an electric, the motor just replaces the launch. E-flite's launch advice for the Conscendo Evolution is 1/2 to 3/4 throttle, a javelin-style throw into the wind 5 to 10 degrees above the horizon, then climb to a safe altitude before maneuvering.
Climb, glide, circle
- Climb into the wind to a comfortable height, then throttle to zero and let the prop fold.
- Trim for a smooth, slightly nose-down glide. Fly gentle straight lines across the field.
- When the model shows lift, fly a little farther in, then start circling.
- Near the ground, pull tight circles to stay in the core. As the model climbs, open the circle up.
- If one side of the circle feels stronger, shift the circle toward it each lap.
- Drift with the thermal, but keep enough height to get back upwind to the landing area.
- When lift fades or you hit sink, leave in a straight line at a slightly higher speed and look for the next one.
Speed is life
Garwood sums it up in three words. Stalls are the most common cause of crashes on launch and landing, and a stall in a turn near the ground is how most gliders die. Keep the speed up in turns and fly smoothly. Jerky inputs cause "stick lift," where the model climbs for a moment because you pulled, not because the air rose. With a polyhedral rudder-elevator glider, let the model fly itself; too much rudder input can make it sink.
Landing
Land directly into the wind to keep ground speed low. Judge your sink rate and aim for the middle of the landing area, slowing with light back stick and easing back to flare just before touchdown. E-flite notes the Conscendo won't slow down as easily as most park flyers and needs more landing room. Set a 5-minute timer for the first few flights, as the manual suggests, until you know how much battery a climb uses.

3. Folding Props: How They Work and How to Set Them Up
A fixed prop is a big source of drag in a glide. A folding prop's blades hinge on a yoke, so centrifugal force swings them out under power and airflow folds them back along the nose when the motor stops. A good fold makes a powered glider glide almost like a pure sailplane.
The parts of a folding prop
A folding setup is a kit of four parts: the blades, a yoke (or hub) that holds them on pins, a spinner and a collet that clamps to your motor shaft. Aloft Hobbies' description of CN Models spinner assemblies is a good example: 3 mm blade pins, collets sold separately in shaft sizes, and an offset yoke so the blades fold closer to the fuselage for less glide drag. You may need to trim the nose cone slightly so the blades swing through their full range.
Turn the ESC brake on
This is the step people miss. If the motor freewheels at zero throttle, the airflow windmills the prop and the blades never fold. Spektrum's Smart ESC programming guide lists the Avian brake as "Disabled" by default, where the motor freewheels at zero throttle, with a "Normal" brake option and adjustable brake force. Other ESC brands have similar settings. For a folding prop, enable the brake, then test: run the motor up, cut the throttle and confirm the prop stops and the blades fold. A factory-built electric glider should already be set up this way; check yours before the first flight.
Choosing blade size
Folding blades are sized diameter x pitch like any prop, and they load the motor the same way. Use the motor maker's recommended range and a watt meter to confirm current. APC's suggested RPM limit for its folding electric props is 120,000 divided by diameter, lower than the 150,000 for its thin electric props. Check your blade maker's rating before putting folding blades on a hot setup.
Field checks
Before each session, check that both blades swing freely and fold evenly. A blade that sticks open adds drag and vibration. Check the spinner and collet are tight, and look for cracked blade roots after any hard landing.

Conclusion
Thermal flying rewards patience more than reflexes. Learn your glider in calm air, then go out on a sunny day with puffy clouds and watch the model as closely as the sky. Circle where it rises, keep the speed up, don't drift too far downwind, and land into the wind. On an electric glider, make sure the brake is on so the prop folds. The first time you climb out of sight with the motor off, you'll understand why glider pilots grin so much.
Want help choosing a glider or setting up a folding prop? Stop by our Cumming showroom or browse our gliders. You can also contact us with questions.
Gear Mentioned in This Guide

E-flite Conscendo Evolution 1.5m BNF Basic with SAFE Select
A 1.5 m electric glider with a folding prop, AS3X and optional SAFE Select; hand-launched.
Shop now
E-flite UMX Conscendo BNF Basic with AS3X and SAFE Select
An ultra-micro motor glider with a folding prop, AS3X and SAFE Select, for calm-evening glide practice.
Shop now
Aeronaut CAM 11x8 Folding Blades
Folding blades for an electric glider conversion; pair with a matching yoke, spinner and collet.
Shop now
Streamer Hand Launch Glider
A cheap way to learn how air moves over a field before you risk an RC model.
Shop nowFrequently Asked Questions
What is the best RC glider for a beginner?
An electric glider with stabilization is the easiest start, because you can climb again under power whenever you need. The E-flite Conscendo Evolution 1.5m and the smaller UMX Conscendo both use AS3X stabilization with optional SAFE Select.
How do I know my glider is in a thermal?
Watch the model. A rising tail or nose, a wing lifting, the model speeding up or climbing without input all suggest lift. Soaring hawks, bugs or fluff rising, and sudden warm, calm air at the flight line are also signs.
Why won't my folding prop fold?
Usually the ESC brake is off, so the prop windmills in the airflow. Enable the brake in the ESC settings. If it still won't fold, check that the blades pivot freely and don't rub the spinner or nose.
Which way should I circle in a thermal?
Either way works. Circle tightly near the ground to stay in the core, open the circle as you climb, and shift toward the side of the circle where lift feels strongest.
What time of day is best for thermals?
Midday on a sunny day with puffy cumulus clouds is usually best. Early morning and evening air is smoother, which is better for practicing trim and landings.
How do I launch a pure glider without a motor?
Small gliders can be hand launched for practice. Larger sailplanes often use a hi-start: a ground stake, rubber tubing and line with a parachute and tow ring. You launch into the wind at about 45 degrees, and the model gains most of its height in the first third of the tow.


