
The Turbo Timber Evolution is the RC airplane equivalent of a pickup truck with a lift kit and a canoe on the roof. It lands short, hauls itself off grass, wears floats for lake days and comes with LED lights for flying at dusk. Most of its "upgrades" are already in the box, which is great. It also means many owners never fit half of them, or fit them without changing the setup to match.
This guide covers the changes we make most often on Turbo Timber Evolutions at our flight desk: fitting the floats and flying off water, choosing slats or no slats, tuning the flaps and their elevator mix, looking after the three-blade prop, picking batteries and keeping the lights working. Setup numbers come from E-flite's manual for the original Turbo Timber Evolution 1.5m (EFL105250). The version on shelves now, EFL105250B, adds a 70-amp Avian Smart Lite ESC, an AR637TA receiver and heavier landing gear springs, and comes with its own manual. Treat our numbers as a starting point and check them against the manual in your box; where they differ, the manual in your box wins.
The Short Answer
The best Turbo Timber Evolution upgrades cost little or nothing: fit the included floats and slats when the flying calls for them, start the flaps from the factory 20 mm and 35 mm with the matching elevator mix (check your manual), keep the stock 11x7.5 three-blade prop balanced, and fly a 4S pack in the recommended size range.
- Floats: included with the current BNF Basic; learn the plane on wheels first, then fly off water with a spotter.
- Slats: on for slow-flight and short landings, off for speed, per E-flite.
- Flaps: half flap 20 mm with 16% elevator mix, full flap 35 mm with 30%; adjust the mix in small steps at altitude.
- Power: the original manual recommends a Spektrum Smart 4S 3200mAh pack and a 4-minute timer for first flights; Horizon lists 3S or 4S packs from 2200 to 5000mAh for the current version.
1. Floats and Water Flying
Horizon lists a set of optional-use floats with steerable rudders in the Turbo Timber Evolution 1.5m BNF Basic box. Water flying is the most fun you can have with this plane, and also the easiest way to drown a receiver, so take it in order.
Assemble and fit the floats
- Attach the cross members to the floats.
- Join the front and rear struts with the float plates and the 2.5 x 25 mm screws, then add the front support members.
- Remove the wheeled landing gear and mount the float set under the fuselage. The original manual uses two 3 x 10 mm self-tapping screws at the back and two at the front.
- Connect the float rudder wires and check that the water rudders are connected and operating with the main rudder.
- Recheck the center of gravity: 60 mm (plus or minus 5 mm) back from the wing leading edge at the root, measured without slats.
Taxi, step, takeoff
The manual is specific here. Taxi at low throttle, steer with the rudders and hold up elevator to keep the water rudders in and the float noses above the surface. Never apply down elevator while taxiing or during the takeoff run. For takeoff, set takeoff flaps, hold up elevator and accelerate to bring the plane up on the step, then let it build speed. Don't try to lift off the instant it comes up on the step. Take off and land into the wind.
Landing and the day after
Set landing flaps and fly the approach into the wind. As the plane settles into ground effect, close the throttle fully and hold up elevator to flare. The manual says to always fly from water with a spotter and to stay clear of swimmers, boaters and people fishing. If water splashes into the fuselage, bring the plane to shore, open the battery hatch, remove the water and leave the hatch open overnight to dry. Our own advice: learn the plane on wheels before you try water.
Replacement floats
The parts list in the manual gives EFL5261 for a replacement float set. A cracked float fills with water and drags one side, so replace or repair it rather than flying it.

2. Flaps, Slats and Control Throws
Flaps are where the Turbo Timber Evolution earns its STOL badge. Set up properly, you get a steep, slow approach with no ballooning. Set up badly, the nose pitches up every time you drop them. Start from the factory numbers below, then tune.
| Surface | Low rate | High rate | Expo (low / high) |
|---|---|---|---|
| Aileron | 25 mm up and down | 33 mm up and down | 5% / 10% |
| Elevator | 6 mm up and down | 8 mm up and down | 5% / 10% |
| Rudder | 6 mm left and right | 10 mm left and right | 5% / 10% |
| Flaps | Half: 20 mm down, with 16% elevator mix. Full: 35 mm down, with 30% elevator mix. | n/a | |
Values from the E-flite manual for the original Turbo Timber Evolution 1.5m (EFL105250). Dual rates are 100% high and 70% low, and that manual says not to set rates below 50% because AS3X needs the travel. The current EFL105250B ships with its own manual: if its numbers differ, use them.
Set the flap switch
For NX, iX and DX Gen2 radios, the original manual puts flaps on switch D with three positions: up, half (with 16% elevator mix) and full (with 30% elevator mix). The DX8 setup uses Norm, Mid and Land. That manual lists flaps on receiver port 6; confirm the port assignments in the manual for your version. Our RC Airplanes guides cover radio menus if you have not built a flap system before.
Tune the elevator mix
- Climb to a safe height and trim for level flight at about three-quarter throttle with flaps up, as the manual asks for the first flight.
- Fly straight into the wind and select half flap. Watch the nose for 3 to 4 seconds.
- If the nose rises, add 2 to 3% to that flap position's elevator mix. If the nose drops, take some out.
- Repeat at full flap. The goal is a small, steady nose-down glide with no climb when flaps go down.
- Land and write down the numbers. Change only one flap position per flight.
Slats on or off
E-flite's wording is simple: for best high-speed performance fly without the slats, and for maximum slow-speed performance install them. They are glued into their foam pockets with medium CA, so treat them as a semi-permanent choice. If you leave them off, the manual supplies decals to cover the slat mounting points. For float flying from a small pond, we fit them.
Leave sub-trim alone
The manual's troubleshooting table says no sub-trim on this plane. Center surfaces mechanically by sliding the pushrod in the quick connector, then thread-lock and tighten the screw. If you need more than 8 clicks of trim in flight, adjust the linkage to remove it. If you change throws away from the factory settings, the manual warns the AS3X gains may need adjusting too.
3. Prop, Power and Lights
The original manual lists a BL10 800Kv outrunner (EFLM17552), an 11x7.5 three-blade prop (EFL5962) and an Avian 60-amp Smart ESC. Horizon lists a 70-amp Avian Smart Lite ESC for the current 2024 version. The published specs give a 61-inch (1549 mm) span and 559.5 sq in of wing area, and the original manual puts the plane at 2.15 kg with the recommended pack, so it rewards a healthy battery.
Keep the stock prop healthy
The original manual does not list an alternate prop size, so we keep the stock three-blade on. Its job is to work with the motor, ESC and battery as a system. Instead, spend the money on spares and balance: a nicked blade from a gravel strip or a float-plane water strike causes vibration that AS3X has to fight. APC's balancing advice applies to any prop: remove material from the heavy blade, or on electric props, add a little clear tape to the light blade.
Batteries: 3S or 4S
Horizon lists 3S or 4S LiPos from 2200 to 5000mAh with an EC3 or IC3 connector for the current version. The original manual recommends the Spektrum Smart 4S 3200mAh 30C pack, which brings the plane to 75.9 oz (2.15 kg), and sets the telemetry for 4 cells with a 3.4V low-voltage alarm. A 3S pack flies, with less power for climb-outs. Heavier packs shift the CG, so recheck it any time you change battery size. That manual says to set a 4-minute timer for first flights, then adjust once you know your usage. Check your own manual's battery advice if you have the newer version.
Lights and power management
The factory-installed landing, navigation and strobe LEDs plug into the receiver; the original manual lists them on port 5 (Lights). If they stop working after a crash or float mishap, check the lead at the receiver before buying anything. The replacement controller in the parts list is EFLA521.

Conclusion
Most Turbo Timber Evolution "upgrades" are setup, not shopping. Fly it on wheels until it is second nature, then fit the floats with the CG checked. Decide on slats based on where you fly, tune the flap mix one notch at a time, and keep the stock prop balanced with spares in the box. Do that and the plane will land on a sandbar like it was built for it, because it was.
Want a hand? Bring your Turbo Timber to our Cumming showroom and our flight desk will check the CG, flap travel and linkages with you. You can also browse aircraft replacement parts or contact us about a setup session.
Gear Mentioned in This Guide

Turbo Timber Evolution 1.5m BNF Basic V2
The 61-inch STOL bush plane this guide is about, with floats, slats, flaps and LED lights in the box.
Shop now
E-flite 11x7.5 3-Blade Propeller (EFL5962)
The stock prop listed in the Turbo Timber Evolution parts list. Keep a spare in the flight box.
Shop now
Spektrum 4S 2700mAh 30C Smart LiPo (IC3)
A 4S Smart pack inside Horizon's listed 2200 to 5000mAh range, with telemetry on Spektrum radios.
Shop now
Du-Bro Tru-Spin Prop Balancer
Check every new or repaired prop before it goes on the motor.
Shop now
E-flite Float Set: Timber (EFL5261)
The float set the manual lists for the Turbo Timber Evolution, for replacing damaged floats.
Shop nowFrequently Asked Questions
Does the Turbo Timber Evolution come with floats?
Yes. Horizon Hobby lists the current Turbo Timber Evolution 1.5m BNF Basic as including a set of optional-use floats with steerable rudders, plus optional leading-edge slats. Replacement floats are part EFL5261.
Should I fly my Turbo Timber Evolution with or without slats?
E-flite recommends flying without slats for the best high-speed performance and with slats for maximum slow-speed performance. Slats are glued in with medium CA, so pick based on where you usually fly.
What flap settings does the Turbo Timber Evolution use?
The manual for the original version lists 20 mm of flap at half and 35 mm at full, with 16% and 30% elevator mix at those positions. Check the manual for your version, then fine-tune the mix at altitude until the nose stays steady when the flaps come down.
What battery is best for the Turbo Timber Evolution?
Horizon lists 3S or 4S LiPo packs from 2200 to 5000mAh with an EC3 or IC3 connector. The original manual recommends a Spektrum Smart 4S 3200mAh 30C pack. Recheck the center of gravity whenever you change battery size.
What prop does the Turbo Timber Evolution use?
The original manual's parts list gives an 11x7.5 three-blade propeller, part EFL5962, on a BL10 800Kv motor. It does not list an alternative prop, so replace like with like and balance new props before flying.
Can I take off from water on my first flight?
We don't recommend it. Learn the plane on wheels first, then move to water. E-flite's manual says to always fly from water with a spotter.
